Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Access Control Cost in Baltimore?
Gate access control in Baltimore typically runs $350 to $1,400 for a system installed on a gate you already own, with most residential keypad and entry-station jobs landing near $650. A simple keypad swap is on the low end; a multi-unit entry station with intercom and phone access sits at the top. Repairs to an access control system you already have usually fall between $180 and $520, and the written estimate you get after we look at the gate sets the final price.
We’re gate specialists, not generalists. Every call, every technician, and every truck is dedicated to gates, which means we diagnose the mechanical side and the low-voltage automation side together instead of handing half the job to someone else. Electric or manual, we diagnose both sides of the problem. Nine brands. One specialist.
Key takeaways
- Entry-level keypad access control: roughly $350 to $700 installed.
- Mid-range system with telephone or app entry and a gate position sensor: $700 to $1,100.
- Commercial entry station, intercom, or multi-tenant setup: $1,100 to $2,400 and up.
- Repairing existing access control (reader, keypad, wiring, control board): $180 to $520 typical.
- Estimates are free, and we set the price per job in writing before any work starts.
Gate Access Control Cost Breakdown (2026)
The ranges below reflect typical Baltimore-area pricing for parts and labor on access control work. They’re estimates, not quotes. The written estimate is the real number.
| Item | Typical 2026 range | What it covers |
|---|---|---|
| Keypad or card reader replacement | $350 – $700 | Swapping a failed or outdated keypad, reader, or entry device, with wiring checked at the same time. |
| New keypad access control install | $400 – $800 | Standalone keypad wired to an existing operator, including low-voltage run and setup. |
| Telephone or app-based entry | $700 – $1,100 | Entry station or controller that lets a homeowner open the gate from a phone or landline, paired with the existing operator. |
| Intercom and entry station (residential) | $850 – $1,600 | Audio or audio/video entry station mounted at the gate, wired back into the home or a control point. |
| Commercial entry station or multi-tenant system | $1,100 – $2,400+ | Directory, keypad, or card entry for a business or multi-unit property, with wiring or operator work as needed. |
| Control board or reader repair | $180 – $520 | Diagnosis and repair on a failed board, reader, or wiring fault on a system you already have. |
| Loop detector or vehicle sensor | $350 – $900 | Free-exit loop or sensor so the gate opens for a vehicle leaving without a remote. |
| Wiring and low-voltage diagnosis | $200 – $600 | Finding and fixing the connection problem before we touch a reader or controller. |
| Manual gate hardware (latches, hinges, closers) | $200 – $550 | Mechanical repairs on a manual gate that never had automation. |
| New gate install with automation | $3,200 – $9,000+ | New swing or slide gate, operator, access control, and safety devices together. |
Two things push the price up more than anything else: the number of people who need to get through the gate, and whether the wiring already exists. A single keypad on a residential swing gate is one afternoon. A commercial slide gate running high-cycle traffic with a card reader, directory, and intercom is a project. On the low end, you’re often just replacing a reader with an existing low-voltage run in good shape. Anything that requires trenching new wire, replacing a control board, or adding a vehicle sensor moves the number up. A new operator on top of the access control is a separate cost again, and the condition of the gate panels and hinges matters, because a gate that drags will wear out any operator or reader you put on it.
What Affects Gate Access Control Pricing in Baltimore
- Gate type: swing or slide. Swing gates need the reader and operator to work around two hinges and a travel path. Slide gates need the operator, track, and reader aligned along a single rail. The hardware and the labor differ, and so does the price.
- Existing wiring and power. If there’s a live low-voltage run to the gate, we reuse it. If there isn’t, we have to run wire, and that adds time. Poorly buried or damaged wire is often the real fault behind a “dead keypad.”
- Access control method. Keypad, card reader, telephone entry, intercom, and app-based control are not interchangeable in price or complexity. Every layer you add costs parts and setup time.
- Number of users and entries. A residential driveway with one household is simple. A property manager with dozens of tenants, cards that need to be issued and revoked, and a directory that changes needs a system built for that.
- Commercial vs. residential duty. A commercial gate running high-cycle traffic wears parts faster and needs control boards and safety devices rated for that use. The price reflects it.
- Brand on the gate. We work on the brand you already have, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Knowing the operator means we don’t waste billable hours guessing.
How to Save on Gate Access Control
You don’t need to replace what still works. A keypad that’s failed but a control board that’s healthy means you pay for the keypad, not the whole system. A board failure with proven wiring means you pay for the board. The temptation when an entry stops working is to call a general contractor who swaps everything, and that’s where money gets burned. We diagnose first. Nine times out of ten the answer is one failed part, not a whole new install.
- Fix the mechanical gate first. A dragging gate or a bent hinge makes every reader and operator work harder. Correcting the gate is usually cheaper than replacing the automation twice.
- Reuse existing wire when it’s sound. If the low-voltage run is intact, there’s no reason to trench. Ask us to test it before assuming it needs replacement.
- Start with the device you actually need. Not every property needs app-based entry and a video intercom. A plain keypad on a residential gate is a $400 to $800 job installed. The upgrade can wait.
- Consolidate visits. If the gate, the operator, and the entry device all need attention, handle them together. One diagnosis, one wiring check, one visit.
- Get a written estimate before the work starts. The estimate is free, and it’s the number that sets the price. Call (855) 356-2557 and we’ll walk the gate with you.
For the full picture of what we handle across the city, see our Baltimore service page, or start at Baltimore Gate Repair. Both show the three service categories we handle: gate repair, electric gate repair, and gate installation. Nothing else.
Does a Commercial Entry System Cost More Than a Residential One?
Yes. A commercial entry station or multi-tenant system in Baltimore typically runs $1,100 to $2,400 and up, compared with $350 to $800 for a residential keypad. The difference is duty and complexity. Commercial gates cycle far more often, so control boards and safety devices need to be rated for the load. Multi-tenant systems add directory management, card issuing, and often intercom, all of which require setup time. A property manager with a hundred tenants and card-controlled access is a different build than a single driveway gate, and the price should reflect the work, not a menu.
Can You Repair My Existing Access Control Instead of Replacing It?
Usually, yes. Most access control failures trace back to the reader, the keypad, a control board, or a wiring fault, and each of those is repairable at $180 to $520 typical. Replacing everything is rarely the answer. We test the wire, check the operator, and isolate the failed part before quoting. In a lot of cases we’re replacing one component on the same low-voltage run that was there before. If the whole system is genuinely beyond repair, we’ll tell you and quote a replacement, not a patch.
One safety note: the wiring inside an operator and its low-voltage supply is not the place for a DIY attempt. DC and AC live at the same enclosure, and the gate itself is heavy. A trained technician should trace that wiring. We handle both the mechanical and the automation side, and we do it on the brand you already have.
How Much Does It Cost to Add Access Control to a Manual Gate?
Adding access control to a manual Baltimore gate usually runs $1,200 to $3,500, and often more if the gate is heavy or the site needs new wire run. The cost isn’t just the reader or keypad; it’s the operator that turns the gate, the safety devices that make an automatic gate safe, the wiring, and the access control itself. A manual gate that was never automated has no operator, no low-voltage supply, and often no safe travel path. Adding automation means building all of that. It’s worth doing right, because a heavy gate on an underbuilt operator is a hazard, not a convenience.
If you’re not sure whether automation is worth it, we’ll tell you honestly. A gate specialist can look at the gate and tell you what’s realistic at what price. Free estimates.
Why Does Gate Type Change the Price in Baltimore?
Swing and slide gates are built differently and priced differently. A swing gate needs an operator with arms or an underground system, hinges that hold under load, and a reader position that doesn’t sit in the travel path. A slide gate needs the rail, the operator carriage, and a reader aligned along a straight run. Add in the gate size, material, and how many people use the entrance, and you can see why two jobs with the same “keypad” on a quote can land at different numbers. Our experience across swing, slide, and barrier-arm configurations means we size the hardware to the gate rather than forcing a generic package.
Can You Come the Same Day?
Often, yes. Same-day service is part of how we work, and we keep brand-specific parts on the truck so we’re not ordering for a second visit. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. If a gate fails on a Saturday, we’re closed, and a call is booked into the next opening on Sunday. If you’re a property manager with a stuck entry point, tell us the brand and the symptom when you call, and we’ll have the likely part on the truck.
FAQs – Gate Access Control Cost
How much does a keypad gate entry system cost in Baltimore?
A keypad gate entry system in Baltimore typically costs $350 to $800 installed, depending on whether the low-voltage wiring is already there and whether the operator needs work. Call (855) 356-2557 for a free estimate; the written estimate sets the price.
Is it cheaper to repair or replace a gate access control system?
Repair is usually cheaper. Fixing a failed reader, keypad, or control board normally runs $180 to $520, while a full replacement system runs $700 to $1,600 or more. We test first and quote the part that failed. Call (855) 356-2557 for an exact quote.
How much does a commercial entry station cost in Baltimore?
A commercial entry station or multi-tenant system in Baltimore typically runs $1,100 to $2,400 and up, depending on the number of users, directory needs, and whether the operator needs work. Call (855) 356-2557 for a free site visit and estimate.
Can you add access control to a gate that’s already automatic?
Yes, and it’s usually the cheaper version of the job: $400 to $1,100 is typical when a working operator and a sound low-voltage run are already in place. We reuse the existing hardware where it’s safe. Call (855) 356-2557 to set up a free estimate.
What brands of access control and gate operators do you work on?
We’re experienced with nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That covers budget residential swing gates through high-cycle commercial slide operators. Call (855) 356-2557 with your model in hand and we’ll tell you what the job involves.
Contact
Gate access control pricing in Baltimore comes down to the gate, the wiring, and how many people need through it. We’re gate specialists, and every call and truck is dedicated to gate work. Estimates are free, the price is set per job in writing, and we work on the brand you already have. Call (855) 356-2557. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. If you need a full picture of what we handle, see our Baltimore service area page or start at Baltimore Gate Repair.
Pricing reflects the Baltimore market as of 2026. Baltimore Gate Repair offers free estimates – call (855) 356-2557.
What Our Customers Say
"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Latoya Whitfield"Three other companies in Baltimore either didn't pick up or wanted to schedule me for the following week. These guys had someone out the next morning."
- Dustin Hoffman"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, had one with him, and we were moving cars again in under an hour."
- Chris Gallagher